|
|
Terminals, Connectors &
Heatshrink
Plated
Copper Lugs
These UL Listed lugs are made from tin plated copper tubing with 3/8”
holes. They can be soldered or crimped to stranded cable. |
| |
Lug,
Copper, LD, #1 |
$0.95 |
| |
Lug,
Copper, LD, #1/0 |
$1.05 |
| |
Lug,
Copper, LD, #2 |
$0.90 |
| |
"delete"
Use 50-500-260 |
$1.30 |
| |
Lug,
Copper, LD, #4 |
$0.80 |
| |
Lug,
Copper, LD, #4/0 3/8" Hole |
$1.70 |
| |
Lug,
Copper, LD, #6 |
$0.75 |
|
Heavy
Duty Copper Lugs
These cast copper lugs are the best we’ve ever found. They are great
for making high-current battery or inverter cables. |
Compression
Terminals
These solid brass terminals allow good connections to large gauge
wire without the need of special tools or soldering. You just remove
insulation from the end of the cable, insert in the terminal and tighten
the nut with a wrench. |
Heat
Shrink Tubing
Use this tubing to insulate copper lugs and compression terminals.
Tubing shrinks and glue inside melts when heated with a heat gun or
torch, sealing wires against corrosion and moisture. Maximum shrinkage
is listed below. Sold in 6” lengths. |
| |
Heat
shrink, 1", black, 6" piece |
$3.25 |
| |
Heat
shrink, 1", red, 6" piece |
$3.25 |
| |
Heat
shrink, 1/2", black, 6" piece |
$0.96 |
| |
Heat
shrink, 1/2", red, 6" piece |
$0.96 |
| |
Heat
shrink, 3/4", black, 6" piece |
$2.00 |
| |
Heat
shrink, 3/4", red, 6" piece |
$2.00 |
|
Vinyl
Insulated Crimp-on Terminals
These terminals are tin-plated copper with insulated barrels. Terminals
are sold in packages of ten. |
| |
Butt
Splice, Insul., #16-#14 (EACH) |
$0.18 |
| |
Butt
Splice, Insul., #8 (EACH) |
$0.58 |
| |
Butt
Splice, Insul., #12-#10 (EACH) |
$0.20 |
| |
Terminal,
1/4in Tab, #12-#10, Male (EACH) |
$0.20 |
| |
Terminal,
1/4in Tab, #16-#14, Female (EACH) |
$0.18 |
| |
Terminal,
1/4in Tab, #16-#14, Male (EACH) |
$0.18 |
| |
Terminal,
Ring, #8 Wire, #10 Stud (EACH) |
$0.50 |
| |
Terminal,
Ring, #8 Wire, 1/4in Stud (EACH) |
$0.50 |
| |
Terminal,
Ring, #8 Wire, 3/8in Stud (EACH) |
$0.50 |
| |
Terminal,
Ring, #8 Wire, 5/16in Stud (EACH) |
$0.50 |
| |
Terminal,
Ring, #12-#10 Wire, 5/16in Stud (EACH) |
$0.20 |
| |
Terminal,
Ring, #12-#10 Wire, #10 Stud (EACH) |
$0.20 |
| |
Terminal,
Ring, #12-#10 Wire, 1/4in Stud (EACH) |
$0.20 |
| |
Terminal,
Ring, #12-#10 Wire, 3/8in Stud (EACH) |
$0.20 |
| |
Terminal,
Ring, #16-#14 Wire, 5/16in Stud (EACH) |
$0.18 |
| |
Terminal,
Ring, #16-#14 Wire, #10 Stud (EACH) |
$0.18 |
| |
Terminal,
Ring, #16-#14 Wire, 1/4in Stud (EACH) |
$0.18 |
| |
Terminal,
Ring, #16-#14 Wire, 3/8in Stud (EACH) |
$0.18 |
| |
Terminal,
Spade, #12-#10 Wire, #10 Stud (EACH) |
$0.20 |
| |
Terminal,
Spade, #12-#10 Wire, #8 Stud (EACH) |
$0.20 |
| |
Terminal,
Spade, #16-#14 Wire, #10 Stud (EACH) |
$0.18 |
| |
Terminal,
Spade, #16-#14 Wire, #8 Stud (EACH) |
$0.18 |
|
Power
Distribution Block
Use these blocks to split primary power into secondary circuits, or
join cables from a solar array to a power lead-in cable. Install cables
and tighten set screws. They are UL recognized for up to 600 volts.
Terminal blocks are made of zinc plated aluminum for use with aluminum
or copper conductors. 2 poles. Primary side accepts one large cable,
secondary side accepts 6 smaller cables. |
Feed
Through / Splicer Block
Use this block to splice wires of up to #2/0 gauge. They are UL recognized
and CSA certified for up to 600 volts. The terminal blocks are made
of zinc-plated aluminum, for use with aluminum or copper conductors.
2 pole and 3 pole blocks. One connection on each side. |
Split
Bolt Connectors
Use these to splice large wires. They are made from cast copper alloy.
Use for copper wire only. An economical way to splice large wires
or to splice a large wire to a smaller wire. They are often used to
connect a 10 gauge wire from an array to a much larger gauge wire
for the long run to the charge control. Tighten with wrenches and
cover with electrical tape. |
Barrel
Connectors
These UL listed connectors are tin-plated high strength aluminum alloy.
They can be used with copper or aluminum wire. Set screw holds wire
in terminal. Single and double barrel connectors. |
| |
Screw
Lug, #2-#14, 1/4", Single |
$1.60 |
| |
Screw
Lug, #1/0-#14, 3/8", Single |
$2.50 |
| |
Screw
Lug, #2/0-#14, 1/4", Double Duplicate Use 50-501-235 |
$4.90 |
| |
Screw
Lug, #4/0-#6, 3/8", Double |
$10.20 |
| |
Screw
Lug, #4/0-#6, 3/8"n, Single |
$6.20 |
|
|
